doobie 5,802 Posted November 19, 2019 Report Share Posted November 19, 2019 As some might know, I had a fishing float made up of some dowel with a foam indicator as my main float rig. It did it's job very well although sometimes a tangle would occur which was always easy to undo. However, after re-spooling my reel with lighter mono, I kept getting more and more tangles - some to the point of cutting the line and re-rigging. I decided to try something else and didn't really want to buy the stand shop float. So a bit of look around on Google I saw a guy make some cork floats that looked quite good. Problem was I didn't have any wine corks except 'champagne' corks courtesy of the missus. Being the cheap skate person I am lol, I FB'd my neighborhood for some and received a few - and free Problem was that the rest of the materials for the way I wanted to make the floats was a bit expensive But if I want to make more then the cheaper each one will become, plus the satisfaction of making my own. Here's what I did .... First - drilled holes through the cork and with some wood glue put a 6mm piece of dowel through it and let dry overnight. Second - put a couple bits of wood together with a hole to place the dowel to keep in place whilst sanding. I used 60 grit at first and down to 120 grit to get a smooth finish. This one is a champagne cork. A few different shapes and was also careful on a few not take away the wine 'emblem' on the cork so to give a bit of a different look. Then I cut some safety pins keeping the end ring part that will help attach a bit of weight for buoyancy and leader. I originally used some standard sewing cotton (black) but felt it may not hold overtime, so used some braid on the rest. Put some wood glue over it all to strengthen and let dry overnight. The fifth step was to give some primer to the ends ready for some enamel paint. I used Gesso craft priming paint and let that dry for 3 hours. Then the other end and again let dry for 3 hours. Then some black gloss enamel paint on the bottom of the float. Two coats given and will give a little extra to the braid/ring. The eighth step was giving two coating with a vibrant yellow enamel. Not too bad bad so far and could left without further painting, but decided to add a little decoration before giving three coats of Spar Marine vanish, by dipping the floats straight into the tin. Let them dry well and light sand before next coating. Pat the bottom tips to soak up the excess drips. Turned out reasonably ok for my first effort although a little 'rough around the edges' lol Took a bit of time and few dollars but Softy, Territory Lad, paddlepop and 11 others 14 Quote Link to post Share on other sites
Territory Lad 1,137 Posted November 19, 2019 Report Share Posted November 19, 2019 Not bad Doobs. Looks like they will definately do a job. doobie 1 Quote Link to post Share on other sites
lofty64 1,309 Posted November 19, 2019 Report Share Posted November 19, 2019 Now hopefully , to increase your catch rate lol doobie 1 Quote Link to post Share on other sites
dmck 625 Posted November 19, 2019 Report Share Posted November 19, 2019 Try some bamboo skewers (shaslick skewers). They are thinner and lighter than dowel. Usually very cheap at Coles/Woolworths If you want to go really light go to a craft shop and get styrene foam balls. They are dirt cheap. Hot glue the skewers in to position. After you bind the eyes/swivels/whatever in place, seal with the hot glue. (wood glue may not be waterproof).. 'a course...... you seem to have enuff floats now......... maybe just go fishing!! doobie 1 Quote Link to post Share on other sites
doobie 5,802 Posted November 19, 2019 Author Report Share Posted November 19, 2019 5 minutes ago, dmck said: Try some bamboo skewers (shaslick skewers). They are thinner and lighter than dowel. Usually very cheap at Coles/Woolworths If you want to go really light go to a craft shop and get styrene foam balls. They are dirt cheap. Hot glue the skewers in to position. After you bind the eyes/swivels/whatever in place, seal with the hot glue. (wood glue may not be waterproof).. 'a course...... you seem to have enuff floats now......... maybe just go fishing!! I did think about using the skewers and foam and would be very light. That would be ok casting with the wind (if any) but into it wouldn't be too successful. However might do some anyway for a second choice when needed. Hot glue is good but the Stux epoxy glue is even better and waterproof. And I will go fishing Thanks for the ideas dmck Quote Link to post Share on other sites
southie THE BANGA 2,304 Posted November 20, 2019 Report Share Posted November 20, 2019 Nice one Chief! doobie 1 Quote Link to post Share on other sites
FLOATMAN 108 Posted November 20, 2019 Report Share Posted November 20, 2019 Well done Doobie, love to see people have a go, it's good fun and even better when you catch a fish on your OWN gear. When I make floats with cork and I do sometimes as they have built in casting weight. I try to use the reconstituted cork (Cork particleboard) if you like. It sands down better, you don't get lumps flying off.... the hardest bit as you have discovered is too get a reliable source of good corks from someone who's NOT an alcoholic!!! Champagne corks do seem to be the best... doobie 1 Quote Link to post Share on other sites
dmck 625 Posted November 20, 2019 Report Share Posted November 20, 2019 I'll try to remember to collect my wifes corks for you blokes.... A months collection should supply you for a couple of years..... doobie 1 Quote Link to post Share on other sites
doobie 5,802 Posted November 20, 2019 Author Report Share Posted November 20, 2019 41 minutes ago, FLOATMAN said: Well done Doobie, love to see people have a go, it's good fun and even better when you catch a fish on your OWN gear. When I make floats with cork and I do sometimes as they have built in casting weight. I try to use the reconstituted cork (Cork particleboard) if you like. It sands down better, you don't get lumps flying off.... the hardest bit as you have discovered is too get a reliable source of good corks from someone who's NOT an alcoholic!!! Champagne corks do seem to be the best... Thanks Floatman and I'm hoping for that satisfaction - I'm sure it will happen. The corks I were given seemed to sand down quite well but not sure if they were reconstructed cork or not - not small lumps seemed to have flown off, so maybe they were reconstructed ones. I can get plenty of the Champagne ones and at least the Champer bottles have not become all screw tops yet lol. My issue at the moment though is attaching a small weight. I can attach a small sinker with a bit of wire through the middle and hooking onto the ring at the bottom of the float. But in doing so, it restricts the plastic tubing I'm thinking of attaching to the floats bottom shaft (to thread the main line through). And have a biro pen spring for berley down the line. My 2nd choice is to have no small ball sinker (but still the plastic tubing) and have a shop purchased small berley spring down the line. Both will give buoyancy to the float. Or ... attach the small ball sinker to float ring and have a running main line (with a stopper) say through an attached swivel. How would you do it or what do you do? 23 minutes ago, dmck said: I'll try to remember to collect my wifes corks for you blokes.... A months collection should supply you for a couple of years..... Sounds like my wife Quote Link to post Share on other sites
bjorn2fish 4,610 Posted November 20, 2019 Report Share Posted November 20, 2019 Very cool, great job mate! You'll have to let us know how they go in one of your sessions. doobie 1 Quote Link to post Share on other sites
doobie 5,802 Posted November 20, 2019 Author Report Share Posted November 20, 2019 1 hour ago, bjorn2fish said: Very cool, great job mate! You'll have to let us know how they go in one of your sessions. I will, but only if I catch fish bjorn2fish 1 Quote Link to post Share on other sites
yellow door 1 1,786 Posted November 21, 2019 Report Share Posted November 21, 2019 They look slick Doobie WHen you mention problems with tangles and light line it struck a chord with me. I had very similar problems when trying to cast really heavy floats on light tackle. I found that casting in a large loopy arc and 85% power really help get rid of tangles - this sort of cast wasnt possible on my light bream outfit so I started casting with 14lb pound braid and a snapper stick - that sorted it out. The overhead cast kept everything in alignment and sorted out my issues. This may not be relevant to your rigs but I thought it would be worth mentioning - the loopy cast at nearly full power was the answer to my problems doobie 1 Quote Link to post Share on other sites
doobie 5,802 Posted November 21, 2019 Author Report Share Posted November 21, 2019 54 minutes ago, yellow door 1 said: They look slick Doobie WHen you mention problems with tangles and light line it struck a chord with me. I had very similar problems when trying to cast really heavy floats on light tackle. I found that casting in a large loopy arc and 85% power really help get rid of tangles - this sort of cast wasnt possible on my light bream outfit so I started casting with 14lb pound braid and a snapper stick - that sorted it out. The overhead cast kept everything in alignment and sorted out my issues. This may not be relevant to your rigs but I thought it would be worth mentioning - the loopy cast at nearly full power was the answer to my problems Pretty drawing Yellow Door Yeah, that could have helped but it just seemed to be a random big tangle. Previous to changing to a lighter line there was an odd very small tangle that usually came undone with a jerk of the rod. But the lighter line caused big issues. Went to Bunnings today to get some clear tubing to hold line on float. Tubing was either too small to fit on shaft or too big which would slip off. Purchased some electrical cable and took the wiring out - line still slips through too easily, so looks like I'll need to put a couple of half hitches of line to the shaft to hold on. Not my preferred way, but it will work. yellow door 1 1 Quote Link to post Share on other sites
doobie 5,802 Posted November 25, 2019 Author Report Share Posted November 25, 2019 Well the new floats did their job today. yellow door 1, Squid Inc., FLOATMAN and 4 others 7 Quote Link to post Share on other sites
bjorn2fish 4,610 Posted November 25, 2019 Report Share Posted November 25, 2019 Way to go mate doobie 1 Quote Link to post Share on other sites
keenfisho 1,416 Posted December 14, 2019 Report Share Posted December 14, 2019 Yummo, been awhile since Ive had a feed of gar or even targeted them they were the bread and butter fish my grandpa used to teach me how to fish spent many a trip out in the boat catching them, nan can butterfly fillet them better than anyone doobie 1 Quote Link to post Share on other sites
doobie 5,802 Posted December 15, 2019 Author Report Share Posted December 15, 2019 2 hours ago, keenfisho said: Yummo, been awhile since Ive had a feed of gar or even targeted them they were the bread and butter fish my grandpa used to teach me how to fish spent many a trip out in the boat catching them, nan can butterfly fillet them better than anyone They are a tasty fish for sure and the butterflying is a good skill to have - the grandparents always knew the best ways to catch and fillet Quote Link to post Share on other sites
southie THE BANGA 2,304 Posted December 15, 2019 Report Share Posted December 15, 2019 so tasty nice one mate!! doobie 1 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.